cel code P0103 - Ca peut etre causé par quoi ?

[kamuro]

cel code P0103 - Ca peut etre causé par quoi ?

P0103 Mass or Volume Air Flow Circuit High Input

ca peut etre quoi ?

WRX 04 - 100% stock

[UGCspawn]

P0103 Mass air flow sensor circuit high input. ca aurait de l'allure avec ton overrev que tu as fais. trop d'air est entré, c'est la seule idée que j,ai

[Robert_RS2000]

jai trouver sa une place peut-etre que sa peu aider

P0103 OBD-II Trouble Code
Technical Description

Mass Air Flow (MAF) Circuit High Input
What does that mean?

Basically this means that there is a problem with the Mass Air Flow High (MAF) sensor or circuit. A more technical description would be that the MAF circuit had higher than expected voltage (air flow).
Symptoms

You will likely not notice any serious drivability problems, although there may be symptoms such as a general decrease in power or sluggishness.

Causes

A code P0103 may mean that one or more of the following has happened:

* The MAF may be disconnected, or a wiring connection may be bad
* The MAF sensor may be damaged
* The vehicle computer may be faulty (very rare)

Possible Solutions

The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures:

* Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires.
* Inspect for any air leaks near the MAF sensor.
* Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information)
* Replace the MAF sensor.

[UGCspawn]

The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures:

avoir su, on l,aurait effacé

[PsychoPat]

jai trouver sa une place peut-etre que sa peu aider

P0103 OBD-II Trouble Code
Technical Description

Mass Air Flow (MAF) Circuit High Input
What does that mean?

Basically this means that there is a problem with the Mass Air Flow High (MAF) sensor or circuit. A more technical description would be that the MAF circuit had higher than expected voltage (air flow).
Symptoms

You will likely not notice any serious drivability problems, although there may be symptoms such as a general decrease in power or sluggishness.

Causes

A code P0103 may mean that one or more of the following has happened:

* The MAF may be disconnected, or a wiring connection may be bad
* The MAF sensor may be damaged
* The vehicle computer may be faulty (very rare)

Possible Solutions

The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures:

* Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires.
* Inspect for any air leaks near the MAF sensor.
* Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information)
* Replace the MAF sensor.

Peu tu me dire ou tu prend cet info ? Par PM si tu préfère.

[Robert_RS2000]

jai trouver sa a moment donner

http://www.obd-codes.com/trouble_codes/

y parle pas de tout les code mais y en a une coupe qui donne des idée

[kamuro]

The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures:

avoir su, on l,aurait effacé

ben en tout cas le cel est éteint du cluster !